Wanderlodge Owners Group

Wanderlodge Owners Group (https://www.wanderlodgeownersgroup.com/forums/index.php)
-   M450 (Unique Issues) (https://www.wanderlodgeownersgroup.com/forums/forumdisplay.php?f=113)
-   -   M 450 Ramblings (https://www.wanderlodgeownersgroup.com/forums/showthread.php?t=33919)

Hotvenm 05-16-2019 10:58 AM

M 450 Ramblings
 
I would like to share with everyone some of my experience owning a M-450 for 8 years now.

The most annoying issue I had in the first couple of years was the slide locks not working as designed. The bedroom slide gave me the most problems because the actuator for the rear lock is near the exhaust pipe and was not designed to withstand a lot of heat. It is impossible to remove the actuator at the rear bedroom slide. I know this from experience working with the designer of the actuators, Fabco-Air Inc. in Gainesville Florida. I had removed everything to access the actuator and lock before my arrival and we worked the entire day trying to remove the actuator for repair. You can’t remove it because of a bracket BB welded in place. We were able to take it apart and service it with heat resident seals and it works fine now. The president of Fabco- Air said they would be glad to repair any actuators if you remove them first and bring them to their factory. They will not do any more work on a customer’s coach, as they are not equipped to do so. After doing this I still disabled my locks and have driven it for 25,000 or more miles with no problems.

I know owners that would stop the slide short from going out all the way by an inch so that the lock would not engage and lock. By doing they didn’t have to worry about the slide not coming in the morning they were leaving the campsite.

There is an water and oil separator in the front bay under the driver that needs to be drained on a weekly basis to prevent water getting into the slide lock air lines.

I have upgraded my inverters to Magnum pure sine wave with a modern transfer switch and auto start.

I would recommend having a spare voltage regulator on board. The regulator is in the back bedroom closet and is an easy replace. I replaced mine last spring on the side of the road in Texas.

M&M RV electronics https://www.mmrvelectronics.com have done the electrical upgrades to a lot of 450 owners. M&M has all programing for the M-450 software and also all the software and hardware for the slide controls. They really have been our go to place for anything electrical. In the winter they have a shop on the property of Intellitec in Deland Florida. Intellitec built the switches and modules for the M-450.

I love the 450 and for the most part the repairs have been just your normal stuff. The drive and ride is great and there are some bargains out there.

Sorry for the long post.

Randy Dupree 05-16-2019 10:59 AM

Great post,and good info.
Thanks for the insight.

DW SD 05-16-2019 11:50 AM

That is great and interesting info!
You mentioned the water / oil separator and need to drain. I wonder if the M380 has this. I am not aware of it and wonder if I missed it.

Could you please post a photo of it and / or more information? I had thought it the M380 case, it uses the Bendix Air Dryer for that purpose. But maybe not.

Thank you, Doug

DonB 05-16-2019 12:40 PM

Doug, the air coming from the coach is dried, but air from each of the aux pumps goes directly into the small tank with no drier. The bottom of that tank has a drain. I have no idea if this is in any way similar to the 450 setup, but except when using engine air the slide has "wet" air. I have never gotten much out of that drain.

Buck 05-16-2019 12:41 PM

3 Attachment(s)
Quote:

Originally Posted by DW SD (Post 452201)
That is great and interesting info!
You mentioned the water / oil separator and need to drain. I wonder if the M380 has this. I am not aware of it and wonder if I missed it.

Could you please post a photo of it and / or more information? I had thought it the M380 case, it uses the Bendix Air Dryer for that purpose. But maybe not.

Thank you, Doug


Here are three photos that should get you close.Attachment 61959

Hotvenm 05-16-2019 01:00 PM

Thanks Buck. The water separator is the black canister on the left side back of the air compressors.

DW SD 05-16-2019 01:10 PM

Thanks, all.
Substantial differences between the M380 and M450.
Don - now I remember the outputs of the aux air compressors feeding directly via 3/8" nylon tubing to the slide air tank in the forward driver's bay. I will drain that tank one of these days just to see.

Ambient humidity for me is pretty low, so hopefully, I don't collect much.

And not that much air passes through that tank (I don't have leaks, at least they are very minor).
Good to see traction on the M450 forum. Will be great to add to the knowledge base here. A friend just bought one and is getting familiar with his new machine (1 month).
cheers,
Doug

Buck 05-16-2019 01:31 PM

In addition to the pre-filter water separator that Garland just spoke of, there is a tank drain (comes off of the bottom of the tank). Mine is currently laying under the compressor.


All Aux air goes through the water separator and then into a manifold. From the manifold some goes to the Bendix descant canister and some goes on into the bus. The air from the Bendix canister goes into the aux tank forward of the cabinet door.

b1gsur 05-16-2019 02:14 PM

Quote:

Originally Posted by Buck (Post 452221)
In addition to the pre-filter water separator that Garland just spoke of, there is a tank drain (comes off of the bottom of the tank). Mine is currently laying under the compressor.


All Aux air goes through the water separator and then into a manifold. From the manifold some goes to the Bendix descant canister and some goes on into the bus. The air from the Bendix canister goes into the aux tank forward of the cabinet door.




Not so sure the air routing is correct. The Aux tank is drained by the petcock and the Norgren filter. The Bendix drier to the best of my knowledge, is for the air brake system to keep the water out. You want to exchange that filter often, like every year or 2. Yes, it is expensive ($80+). Unfortunately most do not know it is a maintenance item and have never changed it. But you don't want moisture in your air brake components. (BIG dollars)

Buck 05-16-2019 03:05 PM

2 Attachment(s)
Quote:

Originally Posted by b1gsur (Post 452227)
Not so sure the air routing is correct.

Me either. lol

I've had it all apart due to an air leak at the bottom of the aux tank and also since a unknown water leak had rotted the mounting board that held up a couple of junction areas. That was 14 months ago so I'm probably remembering wrongly.....

So what I am sure of is (because I just went back out and checked) the air from the compressor goes through the Norgren water separator and then into the tank.

A 1/2" line comes from the top of the tank into the Bendix desiccant cartridge and then returns to a junction.

Admittedly, I start to get a little fuzzy here. It goes in a half dozen different directions from here.

There are a couple of solenoids in there as well. Dan, do you have any idea what they go to or are used for?


All times are GMT -4. The time now is 11:18 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.