Wanderlodge Owners Group  
BuyByeBlueBird.com
Donate

Go Back   Wanderlodge Owners Group > Search Forums

Site Search:
Showing results 1 to 25 of 86
Search took 0.00 seconds.
Search: Posts Made By: GregOConnor
Forum: Engine 09-05-2010
Replies: 91
Views: 11,602
Posted By GregOConnor
My cell is 951-830-5997 I'll call you this week ...

My cell is 951-830-5997 I'll call you this week for advice.
Forum: Engine 09-04-2010
Replies: 25
Sticky: 8V92 Article
Views: 28,941
Posted By GregOConnor
Cavitation and bubbles imploding are a hard...

Cavitation and bubbles imploding are a hard concept to understand. ford had issues with cavitation when they bored the 6.9 into a 7.3 which made the cyl walls thinner. I think more important than...
Forum: Engine 09-04-2010
Replies: 45
Views: 12,349
Posted By GregOConnor
the drain pipe to the catch should remain steel...

the drain pipe to the catch should remain steel and conductive to the hot block. if you replace it with rubber or plastic you stand the chance of a clog. may be a good idea to include a pcv filter...
Forum: Under The Awning 08-31-2010
Replies: 20
Views: 2,813
Posted By GregOConnor
Kurt, All the best to you

Kurt,
All the best to you
Forum: General 08-31-2010
Replies: 6
Views: 1,660
Posted By GregOConnor
Thanks Bill found it own his own. My post are...

Thanks
Bill found it own his own. My post are moderated and not posted for hours or days, so I was of little help to his search I thought of calling Randy but I reserve the call for major issues. ...
Forum: General 08-29-2010
Replies: 6
Views: 1,660
Posted By GregOConnor
95 pt water fill switch

I just got off the phone with Bill Moore who is having trouble getting the sporlan to open and allow him to fill the fresh water storage tank. Where is the tank and sporlan valve located on the '95pt
Forum: PT & WB (Twin Axle Pusher Unique Issues) 08-27-2010
Replies: 26
Views: 4,093
Posted By GregOConnor
the rad would go in a bunch easier if you drill...

the rad would go in a bunch easier if you drill out one rivet in the lower body panel. You could then just slide it out I used 2x4's and built a trac to walk it out of the bus myself. replaced the...
Forum: Engine 08-25-2010
Replies: 91
Views: 11,602
Posted By GregOConnor
Leroy, thanks for the reply. I can see that the...

Leroy, thanks for the reply. I can see that the fan kicks in at 195 when I go down a level hwy. the reaction to fanning seems good w/o a grade. I am assuming that it kicks in high rpm.
I thought of...
Forum: Engine 08-22-2010
Replies: 91
Views: 11,602
Posted By GregOConnor
I had a warm trip up rt 38 to Big Bear...

I had a warm trip up rt 38 to Big Bear California with some new heat issues and think it could be fan speed. The same trip last year with like ambient proved a cooler bus. when the temps got to...
Forum: Electrical 08-21-2010
Replies: 24
Views: 8,025
Posted By GregOConnor
these test only show issue if the appliance with...

these test only show issue if the appliance with a fault is plugged in or turned on. its a false sense of security. I test my pool lite with a tennis ball. Its hard to get onw of my rots to open...
Forum: Electrical 08-21-2010
Replies: 9
Views: 2,255
Posted By GregOConnor
I would check Bills heat tape suggestion and...

I would check Bills heat tape suggestion and unplug them first. then remove the face plates find the last plug then start disconnecting them one at a time checking for hot ground continuity at each...
Forum: Electrical 08-20-2010
Replies: 9
Views: 2,255
Posted By GregOConnor
they share a relay that powers them up when on...

they share a relay that powers them up when on inverter. a sort of transfer switch. run it off inverter and check for a short then. that may be a clue that it is the relay
Forum: General 08-12-2010
Replies: 11
Views: 3,788
Posted By GregOConnor
pump

the confusion is between diesel injection pumps aprox $3,000 and liftpumps $100.00 then there are high pressure electric fuel pumps for gas injection systems on newer cars $250.00

a lift pump...
Forum: 'Bird Projects & Modifications 08-01-2010
Replies: 149
Views: 27,114
Posted By GregOConnor
you need to send the tv audio output signal to...

you need to send the tv audio output signal to the wanderlodge amp not the wonderlodge radio, not the speakers.

the wanderlodge radio sends a signal to the wanderlodge amp. interupt this path...
Forum: General 07-31-2010
Replies: 57
Views: 7,353
Posted By GregOConnor
if you cant do it yourself I wouldn't invest the...

if you cant do it yourself I wouldn't invest the money. Its a great project bus for a wrencher. I bet you get 10 g's if it is in good shape otherwise. that is 23,500 if you add what it will cost to...
Forum: BMC (Bluebird Motor Coach Unique Issues) 07-31-2010
Replies: 16
Views: 3,899
Posted By GregOConnor
I look for the reason for failures and I would...

I look for the reason for failures and I would bet this bracket failed because the wrong bolt was used. around the bracket there should be no thread. some bolts have threads that are not mill cut...
Forum: Engine 07-31-2010
Replies: 20
Views: 2,953
Posted By GregOConnor
problem with a heat exchanger 'water to oil' is...

problem with a heat exchanger 'water to oil' is ;a leak may contaminate one or the other. one of the reasons I had my 94pt trans oil2water heat exchanger bench tested. I understand water in the...
Forum: Engine 07-31-2010
Replies: 20
Views: 2,953
Posted By GregOConnor
do you even need one? if you dont run the ac or...

do you even need one? if you dont run the ac or override the fan to the on position. I would just install a big loop of hydraulic line. the cooling system may be built for the extra effort it cost ...
Forum: 'Bird Projects & Modifications 07-31-2010
Replies: 8
Views: 12,086
Posted By GregOConnor
I dont think the misters work by cooling the...

I dont think the misters work by cooling the radiator with water. I think they work by cooling the air and the cooler air has more result with removing heat from the radiator.
for the mister to...
Forum: Engine 07-23-2010
Replies: 92
Views: 26,892
Posted By GregOConnor
look for the reason it failed. I bet it was the ...

look for the reason it failed. I bet it was the prior install of the hub over the bearings. when the hub is pressed on the outside of the bearing the outside ring must bear the force of the press....
Forum: Generators 07-22-2010
Replies: 7
Views: 2,252
Posted By GregOConnor
the temp shut down device is a switch (on-off)not...

the temp shut down device is a switch (on-off)not a sender (variable read). the switch complete or remove the ground like you say. the +power is waiting at a relay for the ground to be either...
Forum: Generators 07-21-2010
Replies: 4
Views: 2,123
Posted By GregOConnor
the kubota is self priming when you open the...

the kubota is self priming when you open the valve. allowing the lift pump to push the fuel back to the tank via this path. with the valve open the lift pump must keep up with both supplying the burn...
Forum: FC (Forward Control Unique Issues) 07-21-2010
Replies: 289
Views: 24,778
Posted By GregOConnor
this is where pinching the return line will...

this is where pinching the return line will supply more of the avaliable fuel to the burn part of the ipump to show the problem. this is also where a screwed supply will not allow for the engineered...
Forum: Engine 07-21-2010
Replies: 31
Views: 6,338
Posted By GregOConnor
anyone of the start batteries can cause an issue...

anyone of the start batteries can cause an issue with the ddec. on commercial truck aps where there are several batteries the computers are fused at the battery bank with inline fuses off only one of...
Forum: Engine 07-19-2010
Replies: 141
Views: 20,987
Posted By GregOConnor
you can forget the jack and use the 'airspring...

you can forget the jack and use the 'airspring drop' to do the work. or use the hwh
here is a good mod for 3208 fans

two speed fan conversion (http://www.youtube.com/v/7oARcMDVjh8&hl=en_US&fs=1)...
Showing results 1 to 25 of 86

 
Forum Jump
Web Search:

All times are GMT -4. The time now is 11:52 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.