What did you do with your Bus today

[Randy Dupree]

Originally Posted by Randy T

Thanks Brian, I wonder if I just took some contact cleaner to the thermostat if it'd help?

Take the cover off and use the cleaner,fixes them all the time!

[Randy Dupree]

I plan on finding those aquahot wires i started looking for a few days ago!
I got into it,then my phone started running over.
Thats the way it works,if your not selling coachs,just start a project!

[Mallie Lennon]

My todo list has had several items from day one, that end up on the bottom of the priority list, Like spot light, radio and new back up camera.
Last week we removed the rotating clothes rack and replaced with ceiling hung rack, making lots more room in the closet. Extended the bed lift struts to allow more access under the bed. But there are always things to do. We do not winterize, so it is necessary to have AquaHot on and working for bay heat to work. So yesterday, I noticed the Hydronic heat in the bath was not getting hot, tho the boiler was up to heat and fans going. I was proud of my self when a single tap on the brass check valve solved the problem.

[dackerman]

Originally Posted by dog2travel

The past two weeks installed a Pioneer DEX-6600BT radio head (Fred Bellows recommendation) Soundstream 4 channel amp- both to replace the Kenwood. (Junked the Kenwood amp for outside bay audio-bad.) kept Kenwood amp for bass speakers; Vizio 40" HD TV; Rear View Safety color backup camera & monitor; Headphone set for listening and not bothering loving wife. All Bose and bass speakers in good condition.

Great to have good audio.

Morey,

Did you take pictures? This is on my to do list (maybe this spring).

[birds_first]

Originally Posted by kybird

I got two of my 4 docking lights working.I had to replace one docking on the front drivers side.also had to replace both seal beams 4411. Going to do the rear ones next weekend with pictures. Also got my driving lights working.now the panic switch works also.

Glad you got the correct bulbs that fit your fixtures

[mpierce]

Put in a new Dometic two way fridge in stainless steel. Wanted the propane to work boon docking. Do not have solar yet.

Also, put in a new Atwood rear bedroom AC, totally remote control. That way we did not have to replace the thermostat and wiring too. Plus, being lazy, can control it while NOT getting out of bed!

[KCSS]

Finished up LED lights in storage compartments.
Have a few rolls of LEDs left over - looking for a place to stickum
I know I will get several suggestions telling me where to stickum

[giderich]

KC, thanks for the heads up on the low coolant probe. One more 23503510 is still available from walleye 1000 (Filter Barn) on ebay.

http://www.ebay.com/itm/23503510-DET...-/371170690071

Originally Posted by KCSS

Repaired non working low coolant alarm. New probe required. Found on ebay. Filter Barn. DD part # 23503510. Has 2 more available.

Currently adding LEDs to storage compartments

[al perna]

after 8,000 miles needed some service and repairs.

genny & engine complete service

lube

replace 12 v bathroom Fan

AH service and repair, Engine pre heat line cracked , easy to reach replaced with rubber
hose , will replace with copper after this run .

replaced curb side Height Adjusted Rod , was bent from letting go and hitting the drive axle.

replaced gas shock on curb side front bay door , thanks to Johnnie . ever try compressing that shock ? well you need a ratchet strap to compress that baby !

removed the slide skirt and left it for repair at Parliament , bent when bay door was open during a slide retract ough!!! $1,500.00 ouch !!

hope this will hold me for the next 11k miles

next stop Randy s for some new to me Life Line Batteries

[JamesR]

Removed the snorkel so I could reseal the box to prevent water from draining into the wall and out the weep holes in the engine bay.

Man what a mess. About 5 wasp nests and a gallon of debris. I will clean out all the silicone, wash and reseal with POR-15 and POR putty.

Also finished the corner supports in the engine bay that hold the jump posts, and the electrical boxes for the battery heater, and block heater.







Also cleaned the elbow and hump hose for the filter housing. Treated with dielectric grease.



Finished all of the brackets for mounting the air filter housing back on. I'm not finished in the engine bay so I just have them ready for installation later.