Wanderlodge Owners Group  
BuyByeBlueBird.com
Donate

Go Back   Wanderlodge Owners Group > Mechanic's Corner > M380 (Unique Issues)

M380 (Unique Issues) If you have a unique issue with your M380 model coach and it can't be answered in one of the other forums here, then this is where you can list it.....list your M380 Parts here too.

Site Search:
Reply
 
Thread Tools
  #1  
Old 01-13-2011
gkempse gkempse is offline
Junior Member
 
Join Date: May 2009
Location: palm harbor fL
Posts: 17
Default power issue on front slide module

I was going to put the slide out but the panel was blank The coach is on shore power and the inverter is on. I checked the fuse which was OK. Any suggestions where to check?
__________________

George Kempsell
Palm Harbor FL
2004 M380 "Flying Scotsman"
Reply With Quote
  #2  
Old 01-13-2011
SallySummerlin SallySummerlin is offline
Senior Member
 
Join Date: Aug 2010
Location: Germantown
Posts: 209
Default

George, I would start with the HWH panel in the basement and see if you have power to the master control.
Bruce
__________________
[SIGPIC][/SIGPIC]

Bruce and Sally Summerlin
Germantown, Tennessee
2000 LXi Millinium
Reply With Quote
  #3  
Old 01-13-2011
gkempse gkempse is offline
Junior Member
 
Join Date: May 2009
Location: palm harbor fL
Posts: 17
Default

I think the front slide on the m380 is a blue bird design not hwh? the docs I have show power going to the module in the kitchen cabinet and no other controls I will try to access the module that has the key and check for power
thanks George
__________________

George Kempsell
Palm Harbor FL
2004 M380 "Flying Scotsman"
Reply With Quote
  #4  
Old 01-13-2011
Dan & Cindy Dan & Cindy is offline
Senior Member
 
Join Date: Jul 2009
Location: Broussard
Posts: 701
Default

Ignition switch on, adequate air pressure, transmission in neutral, parking brake set?
__________________
Dan & Cindy
2004 M-380
Broussard, Louisiana
Reply With Quote
  #5  
Old 01-13-2011
gkempse gkempse is offline
Junior Member
 
Join Date: May 2009
Location: palm harbor fL
Posts: 17
Default

All the parameters to activate slide are OK but the panel with the key is totally blank. as I mentioned the fuse is ok so there must be some other function between the fuse or supply and the panel that I cant figure out I assume I can get access to the wiring through the Fluid level panel just above it.
Thanks George
__________________

George Kempsell
Palm Harbor FL
2004 M380 "Flying Scotsman"
Reply With Quote
  #6  
Old 01-14-2011
Doc&Linda's Avatar
Doc&Linda Doc&Linda is offline
Senior Member
 
Join Date: Aug 2009
Location: Bonne Terre
Posts: 537
Default

Hi, Have you looked at the previous posts under M 380 unique issues? The title - Slides front and rear won't move - may address your problem. Hope this helps.
__________________
Doc&Linda
M380 2004
Full-Timing
Missouri
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Front Door Handle Issues (Combined threads) Lee Davis General 93 08-17-2018 12:14 PM
Front Slide Seal Joe Crocker M380 (Unique Issues) 9 08-10-2012 01:40 PM
Help with slide module Andre M380 (Unique Issues) 6 10-02-2010 06:43 PM
Front Slide - Manually retracting Dennis M380 (Unique Issues) 14 09-26-2010 01:06 PM
Possible Safety Issue on PT-40 Gen. Slide RAGster Generators 1 07-18-2008 11:57 AM

Web Search:

All times are GMT -4. The time now is 04:03 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.